
How To Measure Watch Lug Width For Strap Replacement
In this article
To measure watch lug width, take the strap off, rest the watch face-up on a flat surface, and use a ruler or tape measure to measure the gap between the inner edges of the two lugs at one end. That gap is the strap width you need.
The Four Lugs And The Gap Between Them
A watch case has four lugs—two at the top and two at the bottom. Each lug is the metal prong or horn where a strap, band, or bracelet attaches to the case. Lug width is the distance between the two lugs on one end of the watch case, and it is the number a strap maker needs to match. The number printed on a strap indicates the width where it meets the watch, not its overall length, which is why a long strap and a short strap can share the same size figure. If you are replacing a strap, think of this measurement as the attachment point rather than the visible footprint of the watch on your wrist.
Tools That Give A Reliable Number
Calipers or a millimeter ruler are the recommended tools for this job. Calipers let you close the jaws against the inner faces of the lugs and read a clean number, while a ruler works if you sight straight down and keep it parallel to the case. A 1mm measurement error can mean the strap may not fit, so the goal is not a rough guess but a repeatable reading. If your result ends in .5mm, that is likely a calculation error; treat it as a signal to measure again rather than as a real strap size.
Measuring With The Strap Off
Spring bars run between the lugs and hold the strap, so remove them before measuring. Lay the watch on a soft surface with the strap removed; this protects the case and keeps it from sliding while you work. Removing spring bars is easier with the right technique: our guide to swapping a watch strap in two minutes walks through the process, and if you are working with leather, here is how to change a leather strap without scratching the lugs. With the case stable, bring your ruler or calipers to the gap and read the distance between the inner edges. Keep the watch face-up and flat so the lugs sit square to your tool; tilting the case can make the gap look wider or narrower than it is.
Reading The Existing Strap
If the strap is still attached, look for a width marking on the back of the strap. Measure at the top where it meets the watch; do not measure farther down because straps taper. A strap that is 20mm at the lugs may be narrower near the buckle, so a measurement taken lower down will mislead you. Typical whole-number strap widths run between 16mm and 24mm, which makes a clean whole-number reading easy to trust and an odd fraction worth double-checking.
Working With A 21mm Lug Width
If you have a 21mm lug width, a 20mm strap will fit with a 0.5mm gap on each side. That small gap is a fit decision rather than a true 21mm match, so check whether the strap’s material and stitching will hide the space or make it obvious. A 21mm lug width is a good reminder that lug width and strap width are practical partners: the case sets the opening, and the strap has to sit inside it without binding or leaving too much air.
Checking Manufacturer Data
When the watch is not in front of you, search with the format [Brand] [Year] [Model Name/Number] lug width. Manufacturer specs can also narrow the field: Nixon replacement straps and bands come in 16mm, 20mm, and 23mm. For a broader walkthrough of measuring and matching, see our watch lug width guide. Use manufacturer data as a cross-check, not a substitute for measuring the actual watch in your hand, especially if the case has been swapped, polished, or fitted with non-original spring bars.
Matching Strap Width To Wrist And Case
Lug width solves the attachment point, but fit still depends on wrist size and case proportions. Measure your wrist before ordering, and use a watch size guide covering case, lug-to-lug, and fit to see how the strap will sit. A strap that matches the lugs can still feel wrong if the case is too large or the wrist measurement is off. If you want to sharpen your eye for proportions between sessions at the bench, the watch guessing game at Watchdle is a light way to practice.
FAQ
Can a phone app measure lug width accurately?
Camera-based measurement apps are often inaccurate, so they are not a reliable substitute for a physical tool.
Are lug width and strap width the same thing?
The two terms are used interchangeably; both refer to the distance where the strap attaches to the watch.
Do both ends of a watch have the same lug width?
When you measure both ends of the case, both ends give the same measurement.
A new watch to identify is waiting every day at Watchdle.


